Parts and equipment for motorcycles, quads, scooters and bicycles

motorbike deco kit 50

WHICH DECO KIT TO CHOOSE FORAD SUZUKI LTR 450?

SUZUKI LTR 450 graphic kit

What is Graphic kit for SUZUKI LTR 450?

This is a set of stickers that are to be placed on different surfaces of your quad. There's nothing better than a graphic kit to give your machine a second life or give it a style that suits you... all you have to do is glue it on! Here is what you should not miss for a lasting installation.

The graphic kit is the final dressing of your quad. Something to give it a personal touch and make it unique!

You can find standard models, but also kits made according to your tastes and needs, from entry-level products to quality kits manufacturedar professional brands. Easy to replace, graphic kits have become the preferred solutionar those who wish to regularly change the design of their motorized vehicle.

Choose a graphic kit for SUZUKI LTR 450 quad

We offer a wide choice of graphic kits for your quad. All the decoration kits offered are made in France with a high definition print. Ahdes, Kutvek, KRM and Gencod are the main brands sold but you will also find the original manufacturers graphics kits ( Beta, Derbi, Fantic, Gilera, HM, Rieju, Wind).

Ahdes graphics kits

Graphic kits Ahdes

Ahdes is a designer brandar 50 Factory for quad and all-terrain. Graphic kits are made in France and meet the requirements of these disciplines. The vinyl is treated to resist the sun. Graphic kits are exclusives 50Factory.

Kutvek decoration kit

Kutvek graphics kits

Kutvek Graphic Kit specializes in the creation and printing of decoration kits. Easy to install, they bring an incomparable style. The quality of the graphics, the resistance of the support, the colors that do not fade make the brand the leader in graphics kits.

How to install the sticker kit on your SUZUKI LTR 450 quad?

1) Preparation of supports:

- Product to use: Brake degreaser

Degreasing the plastics is the essential step before fitting the graphics kit. If this step is not carried out correctly, your graphic kit will not stick perfectly to the plastics and will not peel off.

Do not put the stickers on scratched plastics. Laying on new plastics is strongly recommended.

CAUTION: New plastics are covered with release wax (invisible to the naked eye). It is imperative to insist on degreasing (5 or 6 cleanings are necessary). Degrease the plastics, insisting on the ends, then dry with a clean, dry cloth.

Gasoline, mineral spirits, window cleaners or "WD" type products should not be used.

2) Positioning of stickers:

Position the sticker on its blank location to see how you will position it.

3) Sticking the stickers:

Always start a permanent collage par the center of the room.

Gradually remove the adhesive from its paper backing as you stick the sticker. Remove air bubbles by pressing firmly outwards with a clean, dry cloth.

IMPORTANT: If the part on which you are working has significant relief, remember to slightly heat the sticker with a hair dryer. This operation will make it more malleable and therefore easier to adapt to the relief and to marry its curve.

4) Finish:

Once the whole kit is in place, heat it up using a hair dryer, taking care to apply pressure again over the entire surface during the heating process. and cooling, precisely on sensitive areas. The action of heat and pressure and time (letting stand at least 48h) will allow the glue to set on the support.

Air bubbles:

If you still see air bubbles, proceed as follows:

- Prick the bubble frankly in its center using a pin and keep the pin pressed.

- Heat the bubble with a hair dryer then remove the pin while continuing to heat.

IMPERATIVE: Let your decoration kit rest for 48 hours, (no rolling!) After the pressure exerted, the glue must have time to "marry" its new support. After these 48h, the adhesion characteristics are at their maximum.


HERE 100% OF THE PARTS INDICATED IN STOCK REALLY ARE!