What is an LED lighting system?

The LED, for Light Emitting Diode, is an electronic component that converts electricity into light. LED turn signals replace your classic bulbs par diodes, which consume less power, produce brighter light and have a longer lifespan.

Popularity of this lighting technology

When it comes to two-wheelers, LED lighting has become very popular in recent years, particularly due to its low energy consumption and longevity. In addition to this, LED lighting offers greater brightness, which improves visibility and therefore safety.

Advantages of this technology for turn signals

Extended life

One of the main advantages of LEDs is their lifespan. While a typical light bulb can last around 1 hours, an LED can last up to 000 hours. This means you won't need to replace your turn signals as often, saving you money in the long run.

Energy Efficiency

LEDs are also much more energy efficient than traditional light bulbs. They use less power, which means they are more environmentally friendly and can also help extend the life of your motorcycle or scooter's battery.

Superior brightness

Another major advantage of LEDs is their brightness. They are often much brighter than traditional bulbs, which can improve your visibility on the road, especially in low light conditions or par bad weather. This can greatly contribute to your safety, as well as that of other road users.

modern design

Replacing the indicators can also have a purely aesthetic purpose. The design of LED indicators with minimalist shapes can redesign the line of your two wheels.

Potential disadvantages of this type of turn signal

Higher cost

LED turn signals have a similar cost to those with bulbs. However, taking into account their lifespan and energy efficiency, they prove to be a profitable investment in the long term.

Potentially complex installation

Installing this type of turn signal may require a little more work than replacing traditional bulbs. In fact, you will probably need to install an LED flasher relay, to prevent your new indicators from flashing too quickly. However, it's not too complex a task and there are plenty of guides online to help you.

If your motorcycle or scooter is equipped with a 12V direct voltage electrical system, it is entirely possible to install LED indicators. Some vehicles with more complex on-board computers may need to start from scratch to accommodate the change. In addition, be sure to select approved turn signals. The majority are approved for the road, but some indicators are not approved.

Conventional bulbs will be replaced par LED bulbs (with lower consumption). If your traditional bulb has a power of 10 Watts and the LED bulb has a power of 1,5 Watts, there will be a gap in the network. It will be necessary to compensate for the disparity by adding one or more resistors, or by adding a new relay. The differential can be adjusted directly on the dashboard of newer motorcycles. If you haven't done this, you will notice that your turn signals are too fast. It is important to remember that the flashing should have a frequency of 90 times par minute, give or take 30.

Before ordering, do your calculations. Your traditional bulbs have a power of 10W, 18W or 21W. Evaluate the charge difference between the traditional bulb and the LED by multiplying par two in order to determine the load to be compensated with the relay or resistors. It is important to provide a resistor for the right indicator and a resistor for the left indicator.

It should be noted that if you do not wish to undertake resistance calculations, you have the option of replacing your central flashing. - for a device compatible with LEDs - or a device that can adjust the flashing frequency.

Guide to choosing the right turn signals

Understand the technical specifications

Before choosing LED turn signals for your two-wheeler, it is important to understand some of the technical specifications. Par For example, brightness is usually measured in lumens, so the higher the number of lumens, the brighter the light will be. You will also need to consider the color of the light, which typically comes in white, yellow, or red. Choose approved ones to avoid a fine in the event of an inspection.

Consider compatibility with vehicle

It is also crucial to check that the LED turn signals you choose are compatible with your vehicle. This will depend on the make and model of your motorcycle, scooter, moped, quad or bicycle. Also make sure that the turn signals comply with your country's road safety standards.

Compare different brands

There are many different brands of LED turn signals available on the market, and they all offer different features and benefits. Take the time to compare the different options and read user reviews to make an informed choice.

Installation of these specific indicators

Preparation and necessary tools

To install your new LED turn signals, you will need some basic tools, such as a screwdriver, an adjustable wrench, and possibly pliers. Before you begin installation, be sure to disconnect the battery from your vehicle to avoid any risk of electrocution.

Installation steps

The installation of your new turn signals begins par removal of old indicators. Once this is done, connect your new LED indicators using the correct connections. Then install the LED flasher relay if necessary. Make an electrical diagram if in doubt, polarity is essential for the proper functioning of the LEDs. Finally, mount the new indicators in their location.

For the rear, remove the saddle then the fairing to proceed in the same way as the front. The resistors will be added to the back car there is more room. Remember to take care of the installation location of the resistors car they will require ventilation, otherwise they risk experiencing a rise in temperature. Don't put plastic around them, don't enclose them in a case. It is possible to install a metal plate and attach them to it. Once you have verified that the turn signals are working correctly, you can reassemble them and reconnect the battery.

Before hitting the road, consider testing your new turn signals again to make sure they are working properly.

Tips for a successful installation

It is advisable not to attempt to install your LED turn signals yourself if you have no DIY or electronics experience. In this case, it would be prudent to call a professional. In addition, after installing your LED turn signals, do not forget to check whether the light intensity complies with current road standards.

Maintenance of these lighting devices

Tips for extending life

To extend the life of your LED turn signals, it is recommended that you clean them regularly to avoid the buildup of dirt or debris that could reduce their effectiveness. In addition, avoid touching the LEDs with your fingers, thisar the natural oil in your skin can shorten their lifespan.

Signs of failure

It's important to know the signs of LED turn signal failure, so you can quickly identify and repair them. The most common signs are a decrease in brightness, irregular blinking, or a blinker that no longer works at all.

Replacing these indicators

Replacing LED turn signals is usually quick and easy. Simply unscrew the old flasher, unplug the cable, then connect the new flasher and screw it into place.

Examples of quality LED turn signals

Recommended brands

Recommended brands include Lampa, Brazzoline, with its attractive aesthetic and superior quality products, and Fifty Parts, a reliable brand offering a wide variety of LED turn signals suitable for all kinds of two-wheelers.

Conclusion: The importance of LED turn signal lighting in safe driving

In conclusion, LED turn signals are a great investment for every two-wheeler owner. Not only do they provide greater brightness, but they also last longer and use less energy than those with bulbs. Plus, they can really give your vehicle a facelift. However, as with any investment, it is important to do your research and choose the right product to meet your specific needs. We hope this article has given you all the information you need to make an informed choice. Good road!

You will find in this category quality turn signals and compatible with many brands of 50cc with box, 125cm3, scooter and maxi scooter like Derbi, Yamaha, MBK, Rieju, Beta, Generic, Piaggio, Peugeot, TNT Motor, Aprilia... etc.